Rebirth 99 to become a car giant.

Chapter 216 Uninvited, Nanshan became a frequent visitor to Huaxia TV

Everyone in the industry has seen the level of Nanshan's gearboxes.

So even if 4MT, 6MT and 4AT are displayed, no one will find it particularly amazing.

After all, there is already a 6AT situation there.

However, the launch of Nanshan's 1.5T turbocharged engine caused a very big impact.

"Mr. Wang, I heard that this engine was specially researched by Nanshan for BYD's new car."

"Although I'm not sure what BYD's new model will look like, if it has such an engine with very good power performance, coupled with the Nanshan gearbox, I'm afraid it will have a very big impact on the market."

"I think we need to reconsider whether Great Wall Motors will continue to purchase its engines from Aerospace Mitsubishi and Dongan Power in the future, or whether it will speed up its own research progress."

Almost all of Zhu Jianbo's attention today was on the engine.

Until now, Great Wall Motors' shortcoming has been its engine.

Even all domestic independent brands have shortcomings in engines.

Although this shortcoming can basically achieve all-round breakthroughs in the next 10 years, in 2003, it was still weak.

Among a group of weak chickens, a Tyrannosaurus rex suddenly appeared, which must have had a huge impact on everyone.

"The research institute and the purchasing department will contact Nanshan together and ask them for the specific parameters and prototype of this engine. We can consider using this product in our new models."

"The fuel consumption is lower and the power is stronger. As long as there is no problem with the quality, there is no reason for us not to use it."

"Of course, we ourselves must speed up engine research. If Nanshan can produce it, there is no reason why we can't."

"We can even discuss with Nanshan, purchase a certain number of Nanshan engines, and then ask them to license our technology."

"It should be much easier to study the engine on this basis."

Wang Ying came to the conclusion without much hesitation.

If there are good things, there is no reason not to use them.

"This is probably a bit difficult. They sell engines and the business can continue."

"But if we are directly authorized to use technology, even if the licensing fee is relatively high, even if we directly purchase their engine technology, it will only cost one or two billion at most."

"But there will be no business in the future."

"If the business continues, even if an engine only earns 1000 yuan, as long as 10 units are produced, there will be a profit of 1 million yuan."

"According to the current development of the automobile market, we can basically consume 10 units a year."

Zhu Jianbo felt that if he were Nanshan, he would definitely not sell the engine technology he had just developed.

Even if a series of restrictions are given, it is still reluctant to sell.

However, Wang Ying didn't see it all for himself and said, "There's no harm in giving it a try. What if someone agrees?"

……

"Chief Fang, someone from Nanshan just introduced that the price of their mold steel is only 20 per ton, which is almost half cheaper than the SKD11 imported from Japan."

"Can your mold department consider verifying whether Nanshan Special Steel can meet our quality requirements?"

Liu Wei, director of the purchasing department of Xifeng Die Punching, also came to Yangcheng to participate in Nanshan Science and Technology Day with Fang Wei, chief of the mold department, and others.

For them, they already have a relatively good understanding of press and mold technology.

Both parties have already cooperated.

But in terms of mold steel, it is the area they are most concerned about today.

As a stamping manufacturer, press equipment and molds are the two most important pieces of hardware.

Among them, in terms of press equipment, various stamping factories generally purchase them from outsourcing, which makes it difficult to reflect their core competitiveness.

Then it depends on the mold involved.

Except for PRG molds and TDM molds, which are mostly purchased from Nanshan, other TDM molds are produced by Xifeng Die Punch's own mold workshop.

In this case, the purchase of various special steels is naturally inevitable in the process of making molds.

In the past, they have not tried to use mold steel from domestic manufacturers such as Baosteel.

It can barely be used on some parts with relatively low difficulty requirements and low precision requirements.

However, in the stamping process of high-strength steel plates, domestic mold steel cannot meet the requirements.

Whether it is the stamping life of the mold or the possibility of problems during the production process, everyone is not at the same level.

This is basically a common situation faced by domestic stamping manufacturers.

"Judging from the mold steel parameters they currently provide, there is no problem at all, and it is no worse than the imported SKD11."

"The next step is to purchase a small batch of mold steel from Nanshan, do some material testing, and try to use it to make several sets of molds."

"If there are no problems, we will naturally switch to Nanshan's mold steel. This way our mold costs can be reduced by at least [-]%."

When Fang Wei left Nanshan, he was specially talked about.

He is now thinking about finding a way to return to Nanshan after three years have passed.

Especially seeing the prosperous situation in Nanshan, he wanted to come back as soon as possible.

Besides, even if there is no such reason, he still supports the use of Nanshan Special Steel simply to reduce costs.

The premise is of course that the materials meet the requirements.

"Before, the group always came to evaluate our localization rate and asked us whether Xifeng Die Punching has achieved 100% localization."

"I didn't have much confidence before, but now even the mold steel can be made in China, and our presses are also made in China."

"Then when the group asks us again in the future, we can confidently say that Xifeng Die Punching has achieved 100% localization."

After Liu Wei said this, Fang Wei wanted to add that some of the standard parts on the mold were imported.

True 100% localization is still difficult.

After all, if you look into it more closely, was the iron ore you originally used for these special steels imported?

……

"Mr. Cao, the people from Huaxia Taiwan are here."

When Cao Yang sent Liu Tianwu away and was about to chat with the general managers of some other customers, Mi Ying quickly came over to report the new situation.

On this Nanshan Technology Day, Cao Yang just asked the sales department to invite various customers and potential customers.

There are really no special invitations to various media.

After all, these technologies are owned by TOB and do not require the help of the media to promote them, nor will they affect Nanshan's business expansion.

Unexpectedly, under such circumstances, Huaxia TV would also be interested?

Has the threshold for joining Huaxia TV become so low?

"Come on, let's go over and take a look!"

No matter what, Huaxia TV definitely has to give them face.

Cao Yang was going to receive him in person.