Start with the aviation industry

Chapter 4 The big men are here

Jiang Haitao took the two of them away, and immediately, the entire technology room was in commotion.

"Little Ma is too lucky. If there is no accident, he will be the supervisor technician of that equipment."

"Niupi, the higher-ups are paying attention to this equipment, Xiao Ma's future is promising."

"That device should be out of the box, I must have a look later."

"."

Everyone was very envious. After talking happily, people left one after another. There is no doubt that they must have gone to see the legendary five-axis linkage CNC machining center on site.

In 1990, such a device was absolutely rare, and only developed countries in the West would have it.

Seeing a lot of people walking away, Lin Feng couldn't hold back anymore, he also went to the production site of the workshop, and looked at a large group of people in front of him from a distance.

After getting closer to see this group of people clearly, I was secretly surprised that almost all the bosses came over, the director of the Phoenix factory, the deputy director of technology, the deputy director of production, the director of the engineering and technology department, the deputy director, the equipment manager, etc. The head of the department and so on.

Whoever is not a bully is a bully in Phoenix Factory who would shake the ground three times when stomping his feet.

The director and technical director of the 406 workshop can only stand aside in front of such a group of big figures. The middle-aged man in the center is the leader of the Phoenix Factory, the factory director Sun Jiangbo. On his left is the technical deputy director Wang Tianfang, and on the right is the production manager. Deputy director Meng Bowen.

It is indeed a key device.

Workshop 406 has already made all the preparations, vacating a spacious enough space. On the terrazzo floor, a large packing box has been opened, and the equipment inside can be seen.

Its main color is milky white paint, and some red. The English and LOG on the machine tool are very eye-catching.

Several installation workers in the equipment department were cautious, as if they were afraid that they would damage the equipment. There were three people beside them. They were not wearing the blue overalls of the Phoenix factory, but trousers, suits, and ties. .

Such attire was absolutely uncommon in 1990. They were commissioned purchasers of this equipment, which is what we call intermediaries now. One of them is in charge, and the other two are technicians.

It is not acceptable for the Phoenix Factory to purchase such equipment directly from Western countries. Even if you have money, you can’t buy them.

The production and manufacture of turboshaft Bajia must have such equipment, so what should we do?

We can only entrust the purchaser, and let them carry out the operation and purchase in the name of a foreign company. After the equipment is bought, it will be shipped to that foreign company first. Foreign companies secretly shipped them to the Phoenix factory.

Fortunately, there was no Internet remote positioning and monitoring in 1990. If it takes more than ten years, it will definitely not be able to do this. People will know as soon as the equipment leaves or enters our country.

The installation of the equipment was careful and careful, and the process was not fast. Maggie stayed on site almost all day, not only watching the installation and commissioning of the equipment, but also conducting training.

Besides him, there are two young workers with high school level.Magee mainly learns programming, and young workers mainly learn how to operate equipment.

However, the two technicians in charge of the training shook their heads and smiled bitterly from time to time. Whether it was Maggie or the two young technicians, the learning effect did not meet expectations.

It's no wonder that in 1990, few people had contact with CNC machining. Although Magee was a college student, he had no contact with this aspect of knowledge in college, let alone the two young technicians.

In the past few days, Lin Feng has basically fully adapted to work and life, especially in the past few days, he has basically reviewed the process regulations in the process technology room of 406 workshop.

There are a total of more than 200 drawing numbers of processing technology regulations, mainly involving the two models of piston six and turboprop six.

Not only firmly remember the processing parameters of each drawing number and each working step, but also remember the technical description of each working step, processing technology diagram, etc.

After reading more than 200 drawing numbers and more than 100 thick processing technology specifications, Lin Feng even started to think about the technical materials in the reference room next door.

Do you want to look through all the technical documents in those cabinets? However, before he had time to read those documents, his eyes fell on the technical manual of this five-axis linkage CNC machine tool.

Do you want to read all these three thick technical manuals?

The idea is tempting.

If you read all these three thick technical manuals, then this machine tool basically has no secrets in front of Lin Feng, whether it is equipment failure maintenance, NC programming, or processing operations and so on.

Maggie's location is not far away. On his big table is a thick technical manual of the five-axis linkage CNC machining center.

This technical manual is one of the three major books, with a thickness of [-] to [-] pages. Every time I read this book, Maggie feels that one head is two big.

In two days, the two teachers in charge of the training will leave, but Magee’s NC programming has not yet been introduced. The teachers said that if you don’t have an introduction now, you can only study this technical manual, which contains detailed programming. Introduction, after thoroughly understanding this book, there is no problem with complex programming.

I have been reading it for a few days, and Maggie has only read twenty or thirty pages.

No, he only read it for about half an hour. After reading only two or three pages, he felt his mind was full of muddleheadedness. He put the technical manual aside and prepared to read it again in the afternoon or tomorrow.

Lin Feng came over with a more sincere attitude, after all, he was asking someone to borrow something.

"Ma Gong, can you lend me this technical manual?"

Maggie glanced at Lin Feng first, and then said with disdain, "Do you understand it? It's all in English. Even if I can't understand it, you must not."

Although Lin Feng felt a little uncomfortable, he was not angry, and continued, "I'll just look through it for a maximum of two hours, and then I'll return it to you."

"You really don't know the heights of the sky and the earth, even I can't understand it, but you want to read it." Maggie said this in a rather ugly way.

Lin Feng's face sank slightly, "If you don't borrow it, don't borrow it. If you don't understand it yourself, it's because your level is poor."

Originally in a good mood, Lin Feng also felt a little better after being teased by Maji so much, so he simply went to the workshop for a walk, as a way to relax.

Entering the manufacturing site, he watched the processing of some parts and saw that there was no problem, so Lin Feng walked to the five-axis linkage CNC machine tool without knowing it.

In a few days, it has been installed and is being debugged. Several debugging technicians are busy, and the technicians of the intermediary company are also cooperating.

The installation and commissioning of this equipment is a key task. Jiang Haitao, the technical director of workshop 406, always comes to have a look whenever he has time, and he happens to be on site now.

Lin Feng's eyes were sharp, and he saw two technical manuals on the work table next to the machine tool. Except for one in Maggie's hand, it seemed that the other two were all here.

　Kneeling for all kinds of support!
　　
　
(End of this chapter)