Beast World Sweet Pet: I rely on the foundation to become a boss

"No, I'll borrow it from Dad." Feng Yi pressed the four corners of the mat with stones, and then went out.

It didn't take long before he came back with two rolls of mats, and now he doesn't need the mats, his father is still quite talkative.

Spread the mat again, and the two of them continued to dry the wool.

"Feng Yi, the wool is all on your head." After finishing the last bit, Luo Yang raised his head and saw Feng Yi holding a few tufts of wool on his head.

It is estimated that it has been a while, and it is almost dry.

"Is there?" Feng Yi lowered his head and patted himself a few times with his hands.

"I'll help you, don't move." Luo Yang approached Feng Yi, reaching out to help him remove the wool hidden in his hair.

"Haha, why are you so stupid, like a child." Luo Yang made fun of Feng Yi while helping him pick wool.

Suddenly, Feng Yi grabbed Luo Yang's wrist.

"what happened?"

"Don't move, you also have it on your head." Feng Yi suddenly approached and said.

Sure enough, Luoyang stopped moving.

"Boom." Feng Yi kissed Luo Yang on the face by helping Luo Yang pick the wool.

"Hey." Someone smirked triumphantly.

"Feng Yi, you liar, hum." Luo Yang viciously grabbed Feng Yi's clothes.

"Boom." He kissed someone directly on the lips.

"Hey." Then someone ran away with a face full of success.

Feng Yi froze on the spot, stretched out his hand to touch his lips, and smirked again.

Now that the wool is in hand, Luoyang begins to recall the spindles and spinning wheels in his memory.

Spindle is quite easy to do.

First use a bamboo piece about [-] centimeters long to polish it into a round shape, and sharpen one end to make it smoother.

A small hole is cut out at the other end to install a horizontal bamboo strip to form a cross, so that it will not slip out when it is put into the round hole of the base.

A concave circle should be engraved in the middle of the spindle, and then a thread should be used to connect the spinning wheel, and the spinning wheel should be used to make the spindle rotate.

Such a simple spindle has been made, and it can actually be used for spinning.

However, Luoyang felt that spinning directly with a spindle was a test of technique, patience, and mainly time-consuming.

So he still needs to build a spinning machine, but this spinning machine is a bit difficult to handle by himself.

There are too many places to cut, so I have to ask Feng Yi for help.

First make a base out of bamboo to hold the spindle and the spindle.

A half-meter-long, wrist-thick bamboo is connected to two U-shaped bases, and the base of the spinning wheel is about half a meter high.

The base of the spindle should be small, as long as [-] cm is enough.

In the two U shapes, the two vertical logs must be dug with suitable holes.

At that time, it will be used to fix the spindle and spinning wheel.

Make two more small windmills, about knee height is enough.

Prepare palm-width bamboo slices and cut them into the same length. Make a hole in the middle of the bamboo slice and put a thin bamboo in it.

The length of the bamboo is less than half a meter, which is enough.

In this way, the two ends of the log were fixed with five pieces of bamboo, and there was a fan blade with windmills on both sides.

Then cut some half-finger-wide thin bamboo strips with the same length as the log, and fix the leaves of the two windmills crosswise to form a stable triangle.

Such a spinning car is ready, and the spinning car and the spindle are installed on the base.

After the spinning car is installed, it is also necessary to make a cross structure on the back to prevent it from slipping out, and then install a 7-shaped handle on the other end to facilitate turning the spinning car.

Finally, connect the spindle to the spinning wheel with a thin cane that fits into the nice indentation of the spindle.

Tighten the fine vines directly and tie the knots, and remove the excess vines.

Luoyang tried to turn the handle of the spinning wheel, and the spindle next to it also turned, and it was successful.

After tossing for a long time, I finally finished the spinning tool before dark.

At this time the wool had already dried, Luoyang and Feng Yi hurriedly put away the wool in baskets.

After collecting the wool, Feng Yi went to return the mat, while Luo Yang prepared dinner.

Just as they were having fun, after the two had dinner, Luoyang turned on the light and asked Feng Yi to help him make a simple nail comb.

It's just a piece of bamboo board with a lot of sharp teeth standing upright, with little gap.

Luoyang excitedly picked up the nail comb and began to comb the wool. The wool was already fluffy and soft, but after combing it, it became even fluffier.

Using a nail comb to comb a large ball of wool, Luoyang twisted out another ball of wool and carefully wound a thread end on the spindle.

Gently turn the spinning wheel, and a wool thread is slowly pulled out from a ball of wool.

Although, due to technical reasons, some places are thick and some places are thin.

But after all, it is done, and the thread can be spun.

"Feng Yi, did you see that I succeeded?" Luo Yang spun a length of thread and shared it with Feng Yi excitedly.