Douluo's Martial Soul Forging Master

After eating, Wan Xuan packed up the lunch box and put it at the door. After all, the people serving Wan Xuan could not be allowed to enter the room. In that case, they would be able to see Aya.

Then Wan Xuan returned to the forging room, the moment Wan Xuan pushed the door open, Lou Gao raised his head, looked at Wan Xuan and shook his head with a smile, then pointed to the iron block in the corner without saying anything .

Wan Xuan instantly understood Lou Gao's meaning, which was to let him choose materials and then forge them, and Lou Gao didn't care about him.

Wan Xuan nodded, and went to the corner to pick out iron blocks. This time, Wan Xuan picked six iron blocks at once. Anyway, Wan Xuan didn't plan to forge only once.

Randomly picked up a piece of iron and threw it into the forging furnace and started to burn it. Next, Wan Xuan re-forged the part that Lou Gao forged before. This time Wan Xuan’s forging speed increased a lot. Let Wan Xuan know what kind of effect each drop of his hammer will produce, so he doesn't have to watch the changes after the hammer falls so carefully, and Wan Xuan's movements are much smoother because of this.

Wan Xuan took a deep breath, then held the iron tongs and threw the forged parts into the quenching pool. A burst of steam rose up, and the cast iron parts lay quietly on the bottom of the quenching pool. The parts that have been forged several times before look better in appearance, but there are still potholes.

"Why is there still a problem? What is the problem?" Wan Xuan looked puzzled and clamped the parts at the bottom of the quenching pool with iron tongs, and wiped off the quenching liquid on the parts with a cloth beside him.

"Although it's better than last time, I still haven't found any problems." Wan Xuan looked at the parts full of potholes.I can't help but start to doubt my talent.

"Bang...bang...bang." Lou Gao didn't draw the blueprint, but raised his head and looked at Wan Xuan while tapping the table with his knuckles.

Wan Xuan rolled his eyes, then closed his eyes to feel the frequency of Lou Gao's knocking on the table, and suddenly Wan Xuan opened his eyes, picked up a piece of iron and threw it into the forging furnace.

Then he closed his eyes again and continued to listen to the sound of Lou Gao's knocking on the table. The force of the knocking was so uniform that there was almost no gap. Wan Xuan gradually became obsessed with the sound of Lou Gao's knocking on the table, it was really wonderful.

Suddenly Lou Gao stopped, Wan Xuan also retreated from this state, opened his eyes, and saw the red-hot iron in the forge.

He quickly picked up the iron block with iron tongs and placed it on the anvil, raised his lower forging hammer, and started forging.

This time Wan Xuan closed his eyes, he was listening to feel what the iron block would look like when he hit it with the hammer.

Then open your eyes to proofread.

In this way, it took Wan Xuan five hours to forge this piece of iron into the desired part shape.

"I feel that it should be successful this time." Wan Xuan looked at the red-hot parts, pursed his lips and nodded.

Then he took a deep breath, mustered up the courage to throw the parts on the iron tongs into the quenching pool, and waited quietly for the steam to rise completely and the parts to cool down completely.

Through the transparent quenching liquid, Wan Xuan saw the parts with only a few potholes inside, and couldn't help being shocked, he succeeded.

Lou Gao banged on the table to remind Dugumo that the force of each hammer was uneven during forging, which resulted in these pits on the surface of the forged parts.

Afterwards, Wan Xuan closed his eyes and listened to the sound to adjust the strength used during forging, so that the force on the iron block would be even, so that there would be no potholes.

But after all, Wan Xuan's strength was not enough to fully grasp the forging hammer, so some potholes inevitably appeared in some places, but there were only a few places, not too obvious.

Lou Gao felt Wan Xuan's gaze raised his head to look at this part, and said, "The control of strength is not something that can be done in a day or two, just practice slowly, and you can't only play this kind of part, it's another matter. You can look at the drawing of a certain part first, and if you don’t understand anything, you can find me.”

Then Lou Gao threw the blueprint of another part in his hand to Wan Xuan, and nodded.

"Thank you, teacher." Wan Xuan took the blueprint that Lou Gao handed over, and then sat on the ground and began to study the blueprint. Lou Gao was very considerate to Wan Xuan, and directly wrote down the forging method, so that Wan Xuan could read it. Understand.

Then Wanxuan quickly forged this part according to Lou Gao's forging method, and there were very few potholes on the part, Wanxuan's forging technology was perfect.

"Okay, the technology is barely enough to be able to forge alone, how about this, you first forge all these parts according to the parts on the blueprint, only half of these blueprints have forging methods, and the forging methods of the other half of the parts need you Explore by yourself, I'll give you three days, and give me the finished product." After finishing speaking, Lou Gao left the study with other design drawings, and left the study to Wan Xuan.

Wan Xuan looked at these blueprints and didn't know what to do for a while.

However, Wan Xuan knew that time was running out, so he first forged these parts with forging methods, and then slowly explored the rest without forging methods.

These parts are not smooth and flat, but have various arcs and corners. According to the forging method of the building height, it is easy to create various corners and arcs. If you do it, it will be a waste of a lot of effort.

However, Wan Xuan is not someone who only knows how to do things recklessly. Wan Xuan quickly found a solution. The key to solving the problem this time lies in the blueprints that Lou Gao handed to Wan Xuan, which already marked the forging method.

Wan Xuan can be sure that the forging methods of these parts without forging methods can be found in the drawings of these standard forging methods.

Wan Xuan first forged the parts that already had a forging method, and then sat on a high-rise chair, began to ponder these drawings, edited the corresponding effects on these drawings, and then reversed them based on the drawings that did not indicate the forging method As for the forging method, Wan Xuan soon rolled out all the blueprints.

When Wan Xuan raised his head again.It was already daylight, Wan Xuan rubbed his eyes, sorted out the blueprints, then stood up and went to the corner, began to pick out iron blocks, and prepared all the parts with a stroke of luck.

Just like that, Wan Xuan reopened the forging furnace and began to forge these materials, trying to forge all the parts this morning.