Survival on the Ice Road at Sea: Obtain a copy system at the beginning

Chapter 217 Making a Short Knife Hilt

The skeletons that Chu Linfeng summoned had no IQ, but they could obey orders mechanically, and it was not a problem to start a fire.

After giving the order to the skeleton, the skeleton began to add wood to the stove, and Chu Linfeng released a ball of fire, which ignited the wood.

The added wood was almost done, so Chu Linfeng asked the skeleton to pull the bellows to increase the temperature, and also inserted two steel bars into it.

"Whoosh..."

The skeleton pulled it up and down, the flame became bigger and bigger, and the temperature became higher and higher.

The temperature of the furnace is very high, and it will soon become unbearable.

At the same time, a lot of smoke was produced, and the warehouse was full of smoke, which was very choking.

But fortunately, there is ventilation in the warehouse. After opening it, the smoke soon disappeared.

The smoke was gone, but the temperature was extremely high, getting hotter and hotter. In the end, the hot Chu Linfeng didn't even wear a vest, but just wore a pair of underpants.

Soon, the steel bars began to glow red.

Chu Linfeng was going to clamp the handle of the short knife between two steel bars, so the steel bars had to be smashed flat.

Since he couldn't hit two at the same time, he could only take out one with pliers, then picked up the hammer and smashed it down hard.

"when!"

Due to the great strength of Chu Linfeng, with a hammer, sparks flew everywhere, and the steel bars were also smashed down.

when!
when!
when!
…………

Then, according to his idea, he smashed one hammer after another, and within a few blows, one end of the steel bar was smashed flat.

Putting this one into the burning coals, Chu Linfeng took out another one and began to smash it, and it was done after a few strokes.

Then the other side of the steel bar is heated and forged.

Until the two steel bars have become long strips.

But then, a problem arose, and he didn't know what to do next.

Looking at the two burning red steel bars, I felt that the second half should be smashed together and fused into a whole.

"Try it, I don't know if it can be smashed into one."

He took out two steel bars, stacked them together, and smashed them down halfway.

when!
when!
when!
........................

After a heavy pounding, the steel strips became thinner and seemed to fuse together, but there was still a crack.

"This won't work, what if it breaks?"

Chu Linfeng is right to worry, if the two steel bars cannot be completely fused together?If the quenching is not good, there will definitely be problems in the end, and cracking is inevitable.

After thinking about it, he thought of folding the back to the front to make four layers and put them together.

In this way, even if it is cracked, it can be guaranteed that all the families will not be separated.

Do it when you think of it.

There was another smack of clanging, and soon the four floors were smashed together.

Also, the width has gotten a lot wider.

This Chu Linfeng is not afraid, just wear it off after the job is done.

After smashing, he put the steel rod into the furnace again, burned it for a while, took it out, and put it directly into the bucket.

Noisy!
Heat rose and filled the car.

Chu Linfeng was also very nervous at this moment. According to the short video he watched, it seemed that quenching was very important.

The heat dissipated, and the steel bar was taken out to see that there were no cracks.

"Beautiful! This is considered a success!"

Chu Linfeng was very excited, he did not expect to succeed the first time.

In fact, it was able to go so smoothly, all thanks to his too strong strength.

With a force of 2000 jin, swinging the hammer with all its strength, just like a hydraulic machine, can smash and deform the steel bar in one stroke.

Of course, building weapons is not all about strength.

But what he made was a handle, and the steel bars needed to be fused together, so it didn't matter if it was stronger.

"At this level, it should be fine, right?"

In my impression, it should be polished.

As for the front part, there is no need to deal with it, as long as it can clamp the handle of the knife.

When the steel bar was completely cooled, Chu Linfeng picked it up and put it in front of him, looking back and forth.

At this time, the front two pieces of the steel bar were separated, and they were smashed together from half to the back. The thickness was relatively moderate, but the width was much wider.

But that's okay, I'm going to start sanding the wide part at the back in a while.

As for drilling the handle and the back of the short knife, I can only try to see if I can drill the short knife.

As long as there is any hope, even if it takes a few hours, the hole must be opened for him.

The following procedures are not so complicated, and most of them are time-consuming.

An hour later.

The steel bar has been polished. Although the shape he wants is a bit short, it is still more than 60 centimeters long.

In addition, the length of the short knife can reach about 80 centimeters, so it is not considered a weapon for pure close combat.

After resting for half an hour and sweating away, it was time to punch holes.

Taking the dagger, took a deep breath.Ready for punching operation.

First, he found the location, and then zoomed in on the hole punch. One hand fixed the short knife firmly, and the other hand began to shake it.

The consoles are all manual, as are the drills.

Whether it is fast or slow depends on shaking.

An operation is as fierce as a tiger.

The drill bit made him shake like a propeller, and sparks flew everywhere where it rubbed against the dagger. , the sound is harsher than when sharpening a knife.

This state only lasted for 1 minute, and Chu Linfeng really couldn't take it anymore. He felt like a train was running in his ears, buzzing.

"Grandma has a leg, and I'll have to get two earplugs in a while. After going on like this, the short knife is done, and I'm fucking deaf."

Rubbing his ears, he glanced at the position of the handle of the dagger.

"Fuck!"

Chu Linfeng was very pleasantly surprised when he saw that there were obvious small holes in the borehole.

Originally, he thought that he would have to work for hours to drill a hole, but he didn't expect that the effect would be achieved now, and it might not take long to get it done.

With motivation, he naturally didn't rest anymore, he just found two things to plug his ears, and continued to work.

As expected, the first hole opened in just over three minutes.

The second takes less time.

Then there is the front part of the steel bar.

Although this thing is thicker than the dagger, the difference in hardness is not usually small, basically it can be drilled out without much effort.

Put the part of the handle of the short knife in the middle of the steel bar, and drilled a hole. It is not very biased, only a little, and there is no need to trim it too much.

The next step is to get two small round sticks and insert them into the holes to fix the handle and blade.

This is not a problem, I took a small piece of the remaining steel bar, and then cut the steel bar into long and short sticks with a short knife, and finally polished it smooth and inserted it.

After all, this was the first time, and it was not inserted perfectly, but after some trimming, there was no problem at all.

"I'm so good, I'm simply a genius."

At this point, the short knife can basically be declared done, the most difficult part has been dealt with, and the rest is to fix and decorate.

"By the way, this brain, I forgot something."

(End of this chapter)